Clause 4, ‘Inherently safe design measures,’ gives examples of geometrical factors that should be considered. Safeguarding and complementary protective measures Step 3: Note that Clause 6. Practical guidance and examples of methods ‘ is intended to assist designers in complying with EN ISO by providing additional guidance on the selection of appropriate protective measures for achieving safety. Clause 6, ‘Information for use,’ outlines what shall be provided. Clause 5, ‘Strategy for risk reduction,’ contains what might be termed the real ‘meat’ of the standard.
|Date Added:||8 August 2014|
|File Size:||68.86 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
However, machine designers should be aware that although Sub-clause 5. General principles isk design or a Type C standard eg BS Inherently safe design measures Step 2: Basic concepts, general principles for design.
Learn more about the cookies we use and how to change your settings. Beware, however, that there is a reference to the ‘lowest practicable’ level of risks from hazards, and the standard does not define this term. Note that Clause 6. One of en iso 12100-2 advantages of modern safety-related control systems is that they can assist with reducing cycle times if, for example, sensitive protective equipment is en iso 12100-2 to initiate the cycle when the operator has cleared the hazardous area.
General requirements for the design and construction of fixed and movable guards deals specifically with the guarding design, but the subject is also covered to a lesser extent in EN ISO Clause 5. These three steps are:. Clause 4, ‘Inherently safe design measures,’ gives examples of geometrical factors that should be considered.
BS EN ISO 12100-2:2003+A1:2009
Safeguarding and complementary protective measures Step 3: EN ISO Safety of machinery – Basic concepts, general principles for design is ne of the most important machinery en iso 12100-2 standards. Subsequent sub-clauses address each of these steps in more detail. EN ISO Part 2 of the standard Technical principles generally contains practical advice that can be implemented when designing machinery.
Safety distances to prevent hazard zones being reached by upper and lower limbs BS EN While the foregoing discusses the body of Part 1 of the standard, there are en iso 12100-2 some additional information included. Safety distances to prevent hazard zones being reached by upper and lower limbs. Clauses 1 and 2 are the scope and normative reference, and Clause isl ‘Terms and definitions’ simply refers the reader to Part 1.
Clause 4, ‘Hazards to be taken into account when designing machinery,’ can be treated as an extensive checklist of hazards, ranging from mechanical, electrical and thermal hazards to hazards generated by noise, vibration and ‘neglecting ergonomic principles in machine design. The bibliography lists eleven ISO and IEC en iso 12100-2 ne machine builders may well 12100–2 to consult, though the bibliography in Part 2 is far more extensive. Fifty documents are listed but, as has been shown above, some of these have since been with withdrawn and superseded.
NBN EN ISO | NBN
What has changed with the “new” standard EN ISO ? – Pilz INT
You may experience issues viewing this site in Internet Explorer 9, 10 or en iso 12100-2 Take the smart route to manage medical device compliance. It is harmonised to the Machinery Directive, so complying with its requirements and those of other relevant harmonised standards will generally be the shortest route to demonstrating that the Essential Health and Safety Requirements of the Directive have been met.
Annex A provides a schematic representation of a machine, though this is likely to be of limited use to most readers, and there are 14 pages of a trilingual English, German and French index of specific terms 12100–2 expressions used in the standard, which is unlikely to be of use to most machine designers.
Part 2 of the standard Technical principles generally contains practical advice that can be implemented when designing machinery. The two parts of ISO can be used independently of other documents or as a basis for the preparation of other type-A standards or type-B or -C standards.
The primary purpose of ISO is to provide designers with an overall framework and guidance to enable them to produce machines that are safe for their intended use.
This website is best iao with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. Each part states that the other is ‘indispensable for the application of this document.